Nearly everybody seems to have their unique thinking about Tools You Need to Install a New Bathtub .
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably challenging project. If the old bathtub is readily accessible, the task can move speedily; if you need to open a wall surface to eliminate the old bathtub as well as place the new bathtub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub and also set in the brand-new one. Make certain you have certified yourself for the task and fit attempting it. Instead of hiring a service provider to take over a halfway-completed task, it is better to think about utilizing one prior to you start. Chances are you may need a professional plumber to make tube connections.
This post will certainly assist you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and also don't need to change the plan of your previous water system pipelines.
Your devices and also product list should make up the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be fairly bothersome because of the restricted access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipes. When the supply pipes have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before carrying on to fit the new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in area in between the tap and the sink. Secure the tap in position with the manufacturer supplied backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type should be connected to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Using the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system and also inspect all joints as well as new pipework for leaks and tighten them if required. Fill the bathtub and additionally examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling and also sealing around the bathtub should wait until the bath tub has actually been utilized a minimum of when as this will resolve it right into its last setting.
Preparing for the Installation
To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to prevent pressure on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its final position.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, causing complications with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components and also fittings. They are offered in tubes as well as cartridges, and also are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to enable the motion experienced when the tub is in use. The sealer can split rather very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very intrigued by A Step-by-Step Guide to Installing a Bathtub and I hope you liked my blog posting. Those who enjoyed reading our blog entry plz do not forget to share it. Thank-you for taking the time to read it.
Click For More Info